A successful alternative to traditional steel pipes is technological products made of metal-plastic. It was especially popular in the plumbing industry. Plastic is used in the assembly and repair of pressure communications, pressureless circuits of hot and cold water supply, as well as heating systems.
In the formation of compounds, a simple and affordable method is used - crimping metal-plastic pipes. We will tell you how this work is done, what tool an independent plumber will need to build or restore systems. Our recommendations will help to achieve the highest quality result.
Crimping: a concept in the broad sense
The very concept of “crimping”, as applied to metal-plastic sleeves, should be considered in the broad sense of the word. For example, crimping is often understood to mean standard tests carried out hydraulically or pneumatically.
But modern practice shows that the term “crimping” also quite logically approaches the procedure for connecting a fitting and a metal-plastic pipe. This type of connection is performed using force crimping technology using a special tool (press pliers).
The photo shows the moment of crimping in the process of joining metal-plastic pipes. In this case, crimping is a mechanical force action aimed at achieving tightness of a reliable connection.
Regardless of the installation conditions and the technologies used, the installation of plumbing or other communications based on plastic pipes is accompanied by tests for tightness and strength.
The connection unit for the crimping pump to the water system on plastic pipes looks something like this. At the input, one of two control pressure gauges is installed, which determines the tightness of the circuit
Typically, the test process is carried out hydraulically. But the possibility of testing pneumatically is not excluded.
Methods of crimping metal plastic
The hydraulic method involves filling plastic pipes with water, followed by an increase in pressure to set values. Tests can affect the entire mounted trunk or only its individual sections.
The pneumatic method involves the use of compressed air instead of water. This crimping method is considered less efficient and more dangerous than the hydraulic version. And it doesn’t matter whether metal pipes or metal-plastic ones are tested.
Image Gallery
Photo from
Construction of a metal-plastic pipeline
Pressure testing of a gas pipe
Plastic pipes in the device of underfloor heating
Plastic pipes in high-rise buildings
Option # 1: hydraulic
The process is no different from the standard version, which is used on steel water mains. The only caveat is that the working pressures for plastic pipes have lower values than those adopted for metal products.
Accordingly, the test pressure is calculated taking into account standard operating pressure settings for plastic according to the formula:
Ri = Rrp * 1.5
In it, Ri is the pressure of the test; Ррп - working pressure of a plastic pipe.
The water temperature inside the pipeline is allowed within the plus values of 5 - 40ºС.
Procedure progress:
- Prepare the test site (put cranes, plugs).
- Install 2 gauges at different points on the line.
- Install an air vent on the upper level of the line.
- At the lower level of the line, connect a water pump.
- Fill the line with water supply from the lower to the upper level.
- Open the air vent to bleed air from the system.
Inside the line of metal-plastic pipes, pressure should be increased slowly, excluding sudden jumps. Such pressure conditions are provided by manual hydraulic press.
A hydraulic pump is used to test an assembled or refurbished system that requires flawless joint tightness. The connections themselves are not formed by the pump
Until the pressure reaches the operating level, it is recommended to periodically check visually the areas of possible leaks.
These sites are usually:
- pipe-to-pipe connections;
- pipe and fitting contact;
- installation points for taps and plugs.
An increase in pressure inside the metal-plastic pipes to a value exceeding the operating parameter by a factor of 1.5 is allowed only in the absence of people near the test line.
The established test pressure inside the pipeline must be maintained for a certain time. For water supply from metal-plastic pipes, designed for operation in domestic conditions, a five-minute minimum exposure period is adopted.
During the accepted minimum value of the test time, a pressure drop at the installation points of the control pressure gauges is not allowed. When changes in minus are observed on the control devices, this condition indicates an incomplete tightness of the system.
It is necessary to relieve pressure to the operating value and carefully check the places of possible leaks over the entire section of the plastic pipes. Detect any defects and repeat the test procedure.
At the final stage of crimping metal-plastic pipes, the pump is disconnected from the system. Control gauges, previously installed plugs and stopcocks are also removed.
Leak tests are passed when they satisfy the following conditions:
- no leaks were visually detected;
- no visual breaks in the walls of the pipes;
- five minutes there was no change in pressure on the control gauges;
- no visible pipe deformations.
Meanwhile, it is necessary to clarify: if the exposure time exceeds a five-minute interval, a slight drop in the test pressure is allowed due to a natural change in the temperature of the water inside the metal-plastic pipes.
Option # 2: pneumatic
In case of impossibility of carrying out hydraulic crimping for any reason, an alternative is allowed - a pneumatic test.
The pneumatic test method differs in a slightly different way of checking for leaks, but in general it practically repeats the hydraulic method. This technology is used not so often on pipes, but for crimping individual devices, for example expansion tanks, boilers, heat exchangers, etc., it is widely used.
A convenient small-sized and lightweight automobile air pump is quite suitable for performing pneumatic tests of a home water system on metal-plastic pipes
To detect leaks under pneumatic pressure testing, as a rule, a soap solution is used. The mounted line is filled with air under pressure Ри = Ррп * 1.15 and the places of potential leaks are irrigated with soapy water. The air outlet is determined by the inflation of bubbles.
This verification technique allows you to visually detect even minor leaks. But it is quite difficult for an inspector to monitor for leaks in places that are difficult to access for visual observation.
The pneumatic test method is quite suitable for testing the tightness of metal-plastic pipe fittings or according to the “pipe in pipe” scheme. But when it is required to test the pipeline system for strength, this method is clearly not the best. Here it is necessary to refer to testing hydraulically.
Crimping as a connection method
The practice of installing metal-plastic pipes is noted by the use of several methods suitable for making all kinds of connections:
- soldering;
- spanner;
- crimp.
The last method of the three is just crimping the metal-plastic pipe in the area of its articulation with the fitting.
The connection of the elements of metal-plastic pipelines by means of power crimping is considered reliable and durable. This technology is rapidly gaining popularity in plumbing.
The technique of such crimping is distinguished by simple actions that are available for execution even to unprofessional plumbers. The only caveat - the work requires the so-called press tongs - a special tool, which creates a reliable crimp connection.
In general, for the execution of work using the crimping technique, the following tool kit is required:
- pipe cutter for plastic pipes;
- calibrator, expander, chamfer;
- press pliers.
The pipe cutter makes an even cut-off for a given size, without deformation of the pipe and at a right angle. With the calibrator and the chamfer, the end of the metal-plastic sleeve is prepared for subsequent articulation with the fitting.
Sometimes an expander is also required for operation. Press tongs in the process occupy a special place. It is with this tool that the prepared compound is crimped.
Crimp and compression (they are also threaded) fittings are used in the assembly of metal-plastic pipelines, the steps of their installation are largely similar:
Image Gallery
Photo from
Before installing the press fitting on the designed place, the connector must be prepared: we disassemble it, remembering how to assemble it in the reverse order
We align the pipeline section in the installation area so that at least 10 cm of pipe are perfectly even. Apply a compression fitting and mark the place of cutting
According to the affixed marks, we cut the pipe so that the cut line is clearly perpendicular to the axis of the pipe
This step applies only if the lines with hot and cold water are laid at a distance of 10 cm or less from each other. We put a heat-insulating corrugation on a hot pipe to prevent condensation from falling out on a cold branch
We calibrate the cut pipe, i.e. processed by sweep to give the correct geometric shape. We chamfer 1 mm from one edge, and remove risks to the other, forming the correct rounded pipe configuration
We install a split ring on the prepared pipe to seal the connection and a union nut
We put the pipe on the fitting until it stops. We take two keys: one hold the fitting, the second hold out the union nut
Following the above algorithm, we install all compression connectors without applying excessive force when tightening
Step 1: Preparing the press fitting for installation
Step 2: Marking for trimming the pipe
Step 3: Trim the pipe to fit the fitting
Step 4: Installing insulation on branches with hot water
Step 5: Sweep Calibration
Step 6: Install the O-ring and union nut
Step 7: Twisting Pipes and Fittings
Step 8: Install Fittings Throughout the Route
How to crimp a plastic pipe
The crimping procedure regarding the connection of a metal-plastic pipe with a fitting provides the following sequence of actions:
- Cutting metal pipes to size.
- Perform calibration of its end sections.
- Chamfering the inner radius.
Then, the crimp sleeve is installed on the end of the pipe.
Elements involved in a crimp joint. The crimping itself is performed by press pliers. This tool is available in different versions - manual and automatic.
After these actions, the fitting part of the fitting is inserted into the metal-plastic pipe from the end where the crimp sleeve is located. Move the crimp sleeve over the pipe body, set it parallel to the fitting. A guide to working with press fittings in the assembly of a metal-plastic pipeline is given here, we recommend that you familiarize yourself with useful information.
Impose on the junction area press tongs, supplemented with accessories corresponding to the size of the diameter of the processed pipeline. Squeeze the tool handles all the way.
A set of installers, which includes press tongs and several nozzles for different diameters of plastic pipes. The cost of such a set can reach up to 100 thousand rubles. depending on brand and configuration
Such actions are typical for crimping using a hand tool. Meanwhile, in addition to manual crimping, there are electric, hydraulic, pneumatic devices.
These design options are usually rarely used in everyday life. Their purpose is industrial production. By configuration, they are also very different from manual models.
It should be noted some features when working with press pliers. Only one-time crimping is always permitted. If for some reason it was not possible to make a high-quality crimp the first time, do not try to repeat the action. Defective crimping must be removed, and the crimping procedure must be performed first.
Image Gallery
Photo from
Step 1: Preparing the Crimp Fitting for Installation
Step 2: Gauge Pipe Edges
Step 3: Crimp the clutch with press pliers
Step 4: Check the tightness of the press joint
Advantages and disadvantages of crimping
Evaluating the connection of metal-plastic pipes made with the help of press tongs, one cannot but note the advantages and disadvantages.
Power crimping technology allows you to create dense non-separable joints. Also, the advantage of this technique is the durability and reliability of the created connection.
Both one and the other determine the conditions where this method is suitable.
The list of noted benefits is as follows:
- an unattended connection is created;
- calculation for high working pressures;
- high mechanical strength;
- long service life;
- Easy, easy and quick installation.
From the point of view of existing shortcomings, experts also identify some factors and usually associate them with the criteria for maintenance or installation:
- a non-separable connection is created;
- special tool required (press pliers).
The downside is that every crimping error reduces all work to zero.
It is necessary to carry out work on crimping a metal-plastic pipe carefully and carefully. The slightest inaccuracy can cause poor-quality crimping. Then you have to start from scratch
In addition to these shortcomings, you can add the high cost of the main tool - a tick press.
True, manual adaptation to domestic conditions has a price not as high as automatic designs. But even in this case, buying is not profitable, since the need of the tool is actually one-time.
From the video you can learn about how to work with mechanical-type press tongs, namely, how to crimp fittings of metal-plastic pipes.
Installation of metal-plastic pipes by crimping is recommended to be performed in ambient conditions with a temperature of at least + 10 ° C. It is advisable to withstand the purchased material (pipes) in the new conditions for at least 24 hours and only then begin installation.
The installed plumbing system must be tested for leaks and strength by means of hydraulic and pneumatic tests.
Do you have experience in working with plastic pipes and in the device of their connections? Do you know the technological subtleties of the production of this work, not covered in the article? Please write comments in the block form below, ask questions, post photos.