Value for money - the fundamental criterion for choosing a shower cabin for a summer residence. It is safe to say that a polycarbonate outdoor shower is a leader among competitors. Having the necessary strength, the material attracts an affordable price and is easy to process.
We will tell you how to properly build and equip a country shower box. The article sets out the technology step by step: from design planning to commissioning a finished building. Based on our recommendations, you will be able to get a convenient, durable and reliable operating point for receiving hygiene procedures.
Polycarbonate: Pros and Cons
Polycarbonate is a synthetic low-combustible material made from extruded polymer granules.
Construction products are available in monolithic or hollow sheets of various colors.
Due to the high mechanical strength combined with minimal moisture absorption, plastic plates confidently displace acrylic and glass used in the construction of greenhouses, garden gazebos and other summer cottages
Polycarbonate meets most of the requirements for the construction of a summer shower:
- Impact resistance. The plastic sheet withstands the vagaries of nature and mechanical stress.
- Manufacturability. Polycarbonate is two times lighter than glass, which simplifies its installation and allows the use of a lightweight frame for cladding. An additional plus is sheet flexibility and the possibility of forming without special equipment.
- Temperature resistance. The material retains its properties in the cold (up to -40 ° C) and in heat.
- Low thermal conductivity. Cellular polycarbonate air gaps retain heat in the building.
Plastic sheets are coated with a protective layer that blocks UV rays - the polymer structure remains unchanged and remains flexible for a long time. The service life of the building with proper care is 7-10 years.
An important advantage of a polycarbonate shower is its low cost compared to alternative constructions of brick, corrugated board or wood
Polycarbonate cladding has some disadvantages:
- low abrasion resistance - the plastic coating is easy to scratch;
- high level of thermal expansion - at minus temperatures, the sheet decreases slightly, and vice versa, increases in the heat.
Defects from temperature deformation can be reduced if the joining of the paintings is carried out using connecting profiles and thermal washers.
Sheets without UV protection are not suitable for outdoor use - under the influence of sunlight they quickly deteriorate, lose their flexibility and crack.
Work plan: what needs to be considered
Before you get down to business, it is worth familiarizing yourself with the theoretical aspects and issues of summer construction. The more construction issues will be resolved at the design stage, the less defects will arise during the assembly and operation of the shower.
Image Gallery
Photo from
Polycarbonate showers
Arrangement of arched forms
Consideration of expansion during fastening and connection
Fog coated polycarbonate
Optimal shower space
The location of the summer shower is selected taking into account a number of factors:
- Illumination With the natural heating of water, a sufficient amount of sun is the basic rule. The tank should not be obscured by trees. For those who prefer evening water treatments, it is better to place a shower from the west of the infield.
- The proximity of communications. Optimally, if there is a sump or sewage pit nearby, this will solve the problem of the disposal of sewage. In addition, you need to plan the water supply in advance and equip the shower closer to the water supply.
- Relief. A small hill accelerates the outflow of water used in hygiene procedures.
If there is no changing room in the shower, then the structure must be installed near the entrance to the house.
An important condition for comfortable showering is the absence of drafts, especially if I will bathe small children. Blowing out a booth can cause illness
The nuances of designing and sketching
A sketch of a summer shower with a lining of polycarbonate sheets is pre-compiled. On it you need to specify the dimensions of the structure, display the type of foundation, the structure of the frame and the method of fastening the tank.
The size of the frame is selected taking into account the individual characteristics of the owners of the cottage. Average values:
- height - 2.2 m;
- length and width - 1 m each.
If there are small children in the family, then the space inside the booth should be slightly increased so that an adult can freely go in and buy a baby.
The presence of the locker room should be planned in advance - it is recommended to allocate 0.7-1 sq.m. Separation between sections is best done with an oilcloth curtain, since it is inconvenient to use the door in a limited space
Some of the nuances of planning a shower:
- A threshold must be set between the locker room and the washing room - this will prevent water from entering the “dry” zone.
- It is necessary to think over the storage system of bath accessories - corner shelves are optimally suited. They are compact and roomy.
- Inside the cabin should be lighting. It is important to choose lighting with a high degree of moisture protection.
- Instead of changing rooms near the shower, you can install racks and sheathe them with polycarbonate, giving the structure an L-shaped shape. The finished structure resembles a beach version of the place for changing clothes.
Given the parameters, a “sketch” is made and the consumption of materials is calculated.
Display of different tank installation options: 1 - under a polycarbonate dome, 2 - without additional shelter. In the first case, the water warms up longer and slowly cools due to the "greenhouse effect"
The following article, which is fully devoted to this interesting issue and the choice of the optimal scheme, will familiarize you with the design of the unit from the shower to the toilet.
Which frame material is better?
The frame of an outdoor shower is constructed of wood or metal. From the point of view of reliability and durability, the metal structure is in the lead, but often, summer residents are guided by the availability of materials and their own working skills.
The most optimal option for strength is a profile pipe. Cons of the material: relatively high cost and the need to use a welding machine.
An alternative method of assembling the frame is to bolt through the corners. Advantages of the method: ease of implementation and the ability to disassemble the frame as a designer
Wood is easier to process, but more capricious to operate. The technology for building a shower of lumber is given in the article, the contents of which we recommend that you familiarize yourself with. For open work, it is advisable to choose larch, cedar or oak. Regardless of the type of wood, the frame needs to be treated with antiseptic compounds that prevent decay.
Water Tank Selection Criteria
The quality of water heating largely depends on the parameters of the tank for a summer shower: material, shape, displacement and heating method.
Material. The market includes plastic and metal tanks. Modern polypropylene containers in some respects outperform analogs of metal.
Features of plastic tanks:
- chemical neutrality - the walls of the vessel do not rust;
- ease of transportation and installation;
- low cost;
- safety of water purity for a long time;
- safety of use paired with heating equipment;
- susceptibility to shock and low temperatures - for the winter, the plastic tank must be removed from the street.
Metal tanks are available in stainless steel, galvanized and carbon steel. The first two materials are durable and resistant to corrosion processes. Rust appears in the black steel tank over time.
Metal tanks for water are equipped with a ball valve, a technical cover and fittings for the hose. In order to minimize the risk of corrosion, zinc containers should be painted
The form. The flat tank is conveniently mounted on the frame and warms up the water faster. A large tank in the form of a parallelepiped is able to completely replace the roof. Water in barrels heats up longer and worse.
The "barrel" version should be resorted to in cases where the installation of the storage tank on a wall or a vertical rack is provided
Volume. Experienced summer residents are advised to select the dimensions of the tank at the rate of 40 liters per person. However, even for a large family, you should not buy a capacity of more than 200 liters, otherwise you will have to additionally strengthen the cabin frame.
Heating method. Conventional tanks are designed for natural heating by the sun. Using different tricks, it will be possible to improve the intensity of the temperature increase:
- painting the tank with black paint;
- tank coating with dark polyethylene;
- arrangement of a closed polycarbonate roof above the tank;
- installation of a foil or mirror from the northern part of the tank, redirecting the sun's rays towards the container.
A more effective way is to use a heated barrel.
The tank is equipped with a heating element, a temperature controller, a temperature control sensor and a thermostat. The country water heater provides the supply of water heated to 50-70 ° C - the indicator depends on the material of the tank walls
But not so simple. The commissioning of heated containers requires the supply of electricity, connecting the shower to the water supply or using a pump, as well as the organization of a control system for filling the tank with water.
You will learn all about the device of a heated summer shower by reading the article recommended by us.
Foundation and drain options
In order to strengthen the design, to prevent waterlogging of the site and the multiplication of the population of harmful insects, it is recommended to erect a shower stall on the foundation. A pile base is suitable for the polycarbonate structure.
Aceid pipes, metal or propylene pipes with a diameter of 10 cm are used as piles. The cavity of the pile is poured with concrete, installing and leading out the anchor spiers for attaching the frame
The organization of the drain system is carried out by one of the methods:
- discharge into a sump or a sewage pit;
- arrangement of a drainage pillow.
Method 1 Under the shower cubicle, a sewer pipe is connected and connected to the drain of the tray. Outside the shower, the pipeline is laid in a trench and approaches the sump.
The role of a septic tank can be performed by Eurocubes for bulk products, the volume of containers is 1000 liters. An alternative is to create a primitive cesspool of tires, barrels, or concrete rings.
The sump should be located remotely from the source of drinking water - at least 20 m. The location near the well or well is fraught with contamination of the water intake layer by harmful microorganisms
Method 2. If the cottage is used for “weekend trips” to nature and a small flow of water is expected, then a simple drainage system is suitable for the disposal of drains.
A hole is dug under the washing section and filled with stone, large and small gravel. Water will naturally be absorbed into the ground. In this case, you can do without a pallet and make a trellised floor of wooden blocks.
Phased construction of a summer shower
From theory, it’s time to move on to practice. Let's analyze step by step the erection of a shower on a pile foundation. Sheathing material - polycarbonate, carcass - wood, drain - drainage system with filter pipe.
Quick photo guide
Consider an example of the construction of a shower cubicle from honeycomb polycarbonate panels, fixed circularly. Water will flow into an absorbing well arranged under a booth. After moving the shower to a new place, you can simply fill it with sand, and cover it with a layer of fertile soil from above.
Image Gallery
Photo from
In a place selected for the construction of the foundation pit, we dig a foundation pit, with a depth of 1.2 -1.5 m, depending on the geological situation. It is important to open the sand into which the water flowing from the shower will “absorb” freely
We fill the pit with an incoherent material with high filtration properties. We fill a third of gravel with a small fraction, another third of the middle and one third of the large. We arrange on top of the formwork from the board and fill the plate, leaving a drain hole in the middle
We fill the foundation plate in two stages. During the second, we form a bias towards the drain hole. At the points of installation of the racks of the future frame, we put mortgages for their fastening. We install the frame racks and fasten cellular polycarbonate to them using screws with thermal washers
We process the drain hole with bituminous mastic for waterproofing. If there is concern about the appearance of fungus on a concrete slab, cover the entire surface with waterproofing protection
According to the dimensions of the shower floor, we construct a pallet from the board, which is fastened with a bar on the bottom side. The design of the pallet should be thought out so that it is freely installed and removed from the box for drying
We put and fix the water tank. Its choice is variable, depending on the preferences and financial capabilities of the owners
We equip the interior of the shower room. Choose a place for attaching the shower head, if available, and shelves for hygiene items
We check the operability of the water supply system, if necessary, eliminate the shortcomings and start operating the shower
Stage 1: Development of a pit for a soil filter
Stage 2: Bottom Shower Device
Stage 3: Assembling the shower frame and installing walls
Stage 4: Waterproofing the concrete slab
Stage 5: Installing the shower tray on the shower floor
Stage 6: Mounting and securing the tank under water
Stage 7: Interior arrangement of a shower box
Stage 8: Pre-Operation Testing
Foundation and drainage pit
Pile foundation installation sequence:
- Mark a place for a shower room, remove a layer of earth from the site, level it, fill it with sand, moisten and tamp.
- Mark the corners of the future building and check the evenness of the diagonals. Permissible error - 2 cm.
- Drill holes with a diameter of 20 cm, a depth of 50 cm
- Pour crushed stone into the pits - the layer thickness is about 20 cm.
- Install metal-plastic sewer pipes (diameter - 10 cm) in each barrel. 15 cm of PVC pipe should remain above the ground.
- Prepare a solution of cement, sand and gravel in a ratio of 1: 1: 2, respectively. With a mixture fill the gaps between the pipe and the walls of the pits.
Pipes can be cut off after a day - the concrete should “seize”. The cut line should be noted using a laser or water level.
Pipe cavities are filled with concrete, anchor bolts are vertically installed inside. Around each pile is a blind area. Construction work continues after 2 weeks, when the solution gains strength
During this period, you can do the drainage system. Progress:
- Dig a pit between the posts with a depth of about 1 m.
- Fill the bottom of the pit with broken brick or large stones. Pour gravel from above, not reaching 10 cm to the surface of the earth.
- The top layer of the backfill is the previously removed turf.
After a while, a new grassy lawn will grow over the septic tank, hiding the location of the drainage.
At the location of the shower tray, a piece of plastic perforated pipe is installed to a depth of 50 cm and displayed outside to the drain hole of the booth. Through it, the drains will be filtered, and enter the drainage system.
Assembling the lower shower harness
For strapping, bars with a cross section of 50 * 100 mm are used, the parts are docked with metal corners. To increase the strength of the assembly, fixing is carried out on both sides of the strapping.
Procedure:
- Assemble a wooden frame - the base of the shower.
- Fix the harness to the foundation with anchors.
- In the center, fix the jumper - a support for the pallet and sex lags.
- From the bars 5 * 5 cm, knock down the frame for the pallet and mount it in the harness. The floor level should be flush with the sides of the pallet.
- On the perimeter of the strapping, install the bars 20 * 20 mm, corresponding to the height of the floorboards.
After trying on the shower “pallets”, you can proceed to flooring with a planed board.
The wood is “customized” in the shape of the pallet and stacked without gaps. The tight fit of the floorboards prevents blowing out the shower stall from below
Fabrication and installation of the frame
The frame is erected from bars 5 * 5 cm, fastened with metal corners and self-tapping screws.
Frame Assembly Sequence:
- Prepare and install vertical racks on the harness. Additionally fix the posts with lumber.
- Cut out the details of the upper harness and screw them to the racks.
- Check the verticality of the pillars and the horizontalness of the base of the roof.
- On the entrance side, mark the doorway by installing the appropriate bars.
- Strengthen structures with jibs.
The finished frame for the summer shower should be checked for rigidity experimentally, swinging the structure in different directions. The frame is supplemented with vertical struts and the evenness of the walls is monitored.
On the upper harness mounted transversely - supports for the water tank. Their number and location depends on the shape and dimensions of the tank
Gable roof device
In the proposed embodiment, a gable roof is provided. To simplify the task, you can make a flat roof or even use an open shower.
Gable assembly technology:
- From rafters to collect some rafters, using metal strips and corners.
- Using the template, make a couple more rafters.
- Lift and install the rafter system on the frame.
- From the slats, make a polycarbonate crate - the fastening step is about 50 cm.
If a soft roof is used (bituminous tiles or rolled material), then a continuous crate is laid.
Under the roofing, waterproofing is placed, the sides are sheathed with a board. Provide ventilation openings for ventilating the shower
Polycarbonate sheathing
All wood elements are pre-treated with high-strength alkyd-urethane varnish. The coating will increase the resistance of wood to moisture and improve the appearance of the building.
After waiting for the frame to dry, you can begin to trim. Thermowells are used for operation. Fasteners are sold complete with o-rings and plugs; self-tapping screws are not provided in the kit.
Thermowells securely and gently press the polycarbonate tightly to the frame. The fastener is UV resistant and compensates for seasonal expansion of the material.
Cell polycarbonate mounting sequence:
- Lay the sheets on a horizontal surface and cut them, holding a sharp knife at an angle of 30 °. The longitudinal cut is made along the honeycomb, transverse in two stages - first, the upper coating is cut, and then the canvas breaks.
- Attach the sheet to the frame and prepare the hole for the fasteners.
- Install the washer and close the screw cap with a plug. Fasteners are not visible inside the structure.
Seal open polycarbonate honeycombs with silicone.
Close the ends of the casing with additional strips. If you neglect this procedure, then the polycarbonate holes will become clogged and overgrown with moss
Finishing work: commissioning
By analogy with the shower enclosure frame, the door is assembled - the frame is knocked down from 5 * 5 cm strips.
The design of the canvas is strengthened by jibs, varnished and sheathed with polycarbonate. After - it is hung on the hinges and the smoothness of the door is checked
Next, the internal arrangement and design of the cabin is carried out: a pallet is installed, a tank is placed, a rubber mat is laid and a curtain is hung.
The pallet "sits" on silicone sealant and is aligned with the floor. The drain hose leads to a perforated pipe recessed into the drainage system.
It is not superfluous to take care of a convenient climb to the locker room and erect small steps of brick and wood.
Brick racks are mounted on a concrete foundation and decorated with natural stone. Floorboards of steps are treated with yacht varnish
Video # 1. Option to equip a shower with a dressing room:
Video # 2. Assembly of the purchased structure and polycarbonate sheathing:
A polycarbonate shower is a practical and affordable option for a summer cottage. The construction technology does not cause difficulties, and the cost of the materials used is quite acceptable. Having spent a little time and secured the support of an assistant, it will turn out to erect a durable construction and improve the conditions of a country house.
Tell us about how you built a shower cabin with polycarbonate walls in your own summer cottage. Perhaps in your arsenal there are technological nuances that will be useful to site visitors. Please write comments, post thematic photographs, ask questions in the block below.